OMakeroot = $(License)$'''
########################################################################
# The standard OMakeroot file.
# You will not normally need to modify this file.
# By default, your changes should be placed in the
# OMakefile in this directory.
#
# If you decide to modify this file, note that it uses exactly
# the same syntax as the OMakefile.
#

#
# Include the standard installed configuration files.
# Any of these can be deleted if you are not using them,
# but you probably want to keep the Common file.
#
open build/C
open build/OCaml
open build/LaTeX

#
# The command-line variables are defined *after* the
# standard configuration has been loaded.
#
DefineCommandVars()

#
# Include the OMakefile in this directory.
#
.SUBDIRS: .
'''

########################################################################
########################################################################
########################################################################

OMakefile = $(License)$"""
########################################################################
# The standard OMakefile.
# You will usually need to modify this file for your project.

# Delete this line once you have configured this file
eprintln($$(CWD)/OMakefile is not configured)

########################################################################
# Phony targets are scoped, so you probably want to declare them first.
#

# .PHONY: all install clean

########################################################################
# Subdirectories.
# You may want to include some subdirectories in this project.
# If so, define the subdirectory targets and uncomment this section.
#

# .SUBDIRS:

########################################################################
# C configuration.
# Delete this section if you are not building C files.
#

################################################
# Configuration.  You might want to modify any of these
# configuration variables.
#

# CFLAGS +=
# ASFLAGS +=
# LDFLAGS +=
# INCLUDES +=

################################################
# Uncomment the following section if you want
# to build a C program in the current directory.
#

# CFILES[] =
#    file1
#    main
#
# MAIN = main
#
# .DEFAULT: $$(CProgram $$(MAIN), $$(CFILES))

################################################
# Uncomment the following section if you want to build a C library
# in the current directory.
#

# LIBFILES[] =
#    file1
#    file2
#
# LIB = libxxx
#
# .DEFAULT: $$(StaticCLibrary $$(LIB), $$(LIBFILES))

########################################################################
# OCaml configuration.
# Delete this section if you are not building OCaml files.
#

################################################
# Configuration.  You may want to modify any of these configuration
# variables.
#

#
# This project requires ocamlfind (default - false).
#
# USE_OCAMLFIND = true
#
# OCAMLPACKS[] =
#    pack1
#    pack2
#
# if $$(not $$(OCAMLFIND_EXISTS))
#    eprintln(This project requires ocamlfind, but is was not found.)
#    eprintln(You need to install ocamlfind and run "omake --configure".)
#    exit 1

#
# Include path
#
# OCAMLINCLUDES +=

#
# Compile native or byte code? 
#
# The default values are defined as follows:
#
# NATIVE_ENABLED = $$(OCAMLOPT_EXISTS)
# BYTE_ENABLED = $$(not $$(OCAMLOPT_EXISTS))

#
# Various options
#
# OCAMLFLAGS    +=
# OCAMLCFLAGS   +=
# OCAMLOPTFLAGS +=
# OCAML_LINK_FLAGS +=
# OCAML_BYTE_LINK_FLAGS +=
# OCAML_NATIVE_LINK_FLAGS +=

################################################
# Generated files
#
# Workaround for the fact that ocamldep does not pay attention to .mll
# and .mly files.
#
# OCamlGeneratedFiles(parser.ml lexer.ml)

################################################
# Build an OCaml library
#

# FILES[] =
#    file1
#    file2
#
# LIB = main
#
# .DEFAULT: $$(OCamlLibrary $$(LIB), $$(FILES))

################################################
# Build an OCaml program
#

# FILES[] =
#    file1
#    file2
#
# PROGRAM =
# OCAML_LIBS +=
# OCAML_CLIBS +=
# OCAML_OTHER_LIBS +=
# OCAML_LIB_FLAGS +=
#
# .DEFAULT: $$(OCamlProgram $$(PROGRAM), $$(FILES))
"""